Subject: mol 0.9.24 works (sort of) 0.9.28 and later don't
From: Peter Canning (canning@vitria.com)
Date: Fri Feb 04 2000 - 18:58:21 MST
I'm trying to run mol on a Apple PowerMac 7300 with a debian installation
running a 2.2.12 kernel. When I installed the 0.9.24 rpm, it booted MacOS
8.1 (the only version of MacOS I've got) and ran fine (except for a problem
accessing files on one of my HFS partitions which I suspect is might be
fixed by 4 Gig partition changes). Unfortunately, when I tried 0.9.28
through 0.9.39, they start to boot MacOS, but seem to hang just before they
should bring up the BootX extension dialog. I set newworld_boot to no, and
comment out the rom_image and oftree in /etc/molrc, so that I can just get
the ROM/oftree from my actual machine. Other than the script output (below)
I haven't been able to get anymore information about what is going wrong.
Here's the output I get from startmol (saved using the script command):
canning-home:~# startmol /boot/System.map-2.2.12
Using MOL library directory /usr/lib/mol
Mac-on-Linux 0.9.30
(C) 1997-1999 Samuel Rydh, <samuel@ibrium.se>
Using resource file '/etc/molrc'
WARNING! Options ignored: /boot/System.map-2.2.12
in_security_mode 0
MOL kernel module 1.1.24
OF Device tree copied from kernel
32MB RAM mapped at 0x20000000
<ROM_FIX> 4096K ROM mapped at 0x4fc00000
<Physical ROM mapping>
ROM checksum = 0x177
Running in PowerPC 604 mode
DEC frequency: 0x00bebc20 (12 MHx), 125:10 mticks/usec
Running on VT 8.
Using console mouse driver
Initing PCI bus services
PCI-bridge 'bandit' (bus 0..0) installed at 0xf2000000
PCI-bridge 'chaos' (bus 1..1) installed at 0xf0000000
GC, Grand Central, (0:16) found
Descriptor based DMA services inited
Using nvram-image 'nvram/nvram.8500.image'
Swim3 floppy driver installed
AWACS disabled
Hammerhead driver installed
Control driver disabled (no pci entry added)
osi_enet: Attached to network interface <eth0>
osi_enet: Ethernet address is: 00 05 02 d6 6c 21
osi_scsi: *** OSI SCSI DISABLED **
53c94 SCSI-driver installed (IRQs 12/0)
Could not register MESH SCSI unit. Need a second bus ??
HFS disk: 255 MB, /dev/sdb [read-write] start: 6390464,
len: 522240
HFS disk: 970 MB, /dev/sdb [read-write] start: 6912704, len:
1986560
HFS disk: 548 MB, /dev/sda [read-write] start: 3078990, len:
1122304
----> (disk_open) Opening /dev/hdb: No such device
----> (disk_open) Opening /dev/hda: No such device
SCSI-Disk (hw-0): 0 MB
driver_mgr_list: hacks console pci gc pic dbdma via-cuda adb nvram escc
swim3 hammerhead mol_video osi_enet scsi
Starting emulation...
Mapping GC at F3000000
dcbi treated as no-op
Unmapping GC
Mapping GC at F3000000
osi_log: DriveControlCmd IGNORED 48
osi_log: kOpenCommand
I'll be happy to try to help diagnose this, if somebody can tell me what to
try.
thanks,
Peter Canning
This archive was generated by hypermail 2a24 : Wed Mar 01 2000 - 00:06:20 MST