Exclude hidden files/folders from backup

[bruce woller]

Dene:

It appears that your tape drive is on the same bus as the Linux system 
but the Mac Os lives on the MESH (built in) bus.  There could be 
competition for the bus when dumping from Linux that is not apparent 
when Mac OS is running.  Since both buses are narrow/slow you could try 
switching the tape drive to the MESH bus and trying to see if that 
makes your dumps go faster in Linux.

Just a thought,
Bruce
On Sunday, April 4, 2004, at 04:08  AM, Dene Stringfellow wrote:

> Thanks again for your replies Michael and Ron.
>
>
> SCSI subsystem driver Revision: 1.00
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> mesh: configured for synchronous 5 MB/s
> mesh: performing initial bus reset...
> scsi1 : MESH
> mesh: rejecting message from target 0: 1 1 3
> mesh: bs0=2f in msg_out
> mesh: rejecting message from target 0: 32
> mesh: bs0=2f in msg_out
> mesh: rejecting message from target 0: f
>   Vendor: SEAGATE   Model: ST32550N          Rev: 3705
>   Type:   Direct-Access                      ANSI SCSI revision: 01 CCS
> scsi2 : 53C94
>   Vendor: ARCHIVE   Model: Python 02830-XXX  Rev: 5.76
>   Type:   Sequential-Access                  ANSI SCSI revision: 02
>   Vendor: MATSHITA  Model: CD-ROM CR-8005A   Rev: 4.0i
>   Type:   CD-ROM                             ANSI SCSI revision: 02
>   Vendor: FUJITSU   Model: M2684S-512        Rev: 2026
>   Type:   Direct-Access                      ANSI SCSI revision: 02
>   Vendor: COMPAQ    Model: ST15150N          Rev: 5217
>   Type:   Direct-Access                      ANSI SCSI revision: 02
>   Vendor: COMPAQ    Model: ST15150N          Rev: 5217
>   Type:   Direct-Access                      ANSI SCSI revision: 02
> st: Version 20020805, bufsize 32768, wrt 30720, max init. bufs 4, s/g
> segs 16
> Attached scsi tape st0 at scsi2, channel 0, id 2, lun 0
> Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
> Attached scsi disk sdb at scsi2, channel 0, id 4, lun 0
> Attached scsi disk sdc at scsi2, channel 0, id 5, lun 0
> Attached scsi disk sdd at scsi2, channel 0, id 6, lun 0
> SCSI device sda: 4194058 512-byte hdwr sectors (2147 MB)
> Partition check:
>  sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10 sda11
> sda12
> SCSI device sdb: 1039329 512-byte hdwr sectors (532 MB)
>  sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5
> SCSI device sdc: 8386000 512-byte hdwr sectors (4294 MB)
>  sdc: [mac] sdc1 sdc2 sdc3 sdc4 sdc5
> SCSI device sdd: 8386000 512-byte hdwr sectors (4294 MB)
>  sdd: [mac] sdd1 sdd2 sdd3 sdd4 sdd5 sdd6
> Attached scsi CD-ROM sr0 at scsi2, channel 0, id 3, lun 0
> sr0: scsi-1 drive
> Uniform CD-ROM driver Revision: 3.12
> PowerMac Z8530 serial driver version 2.0