Dual G5 XServe + Fibre Channel panics

[frenzy at frenzy.org]

I am having a problem with kernel panics after installed a LSI fibre 
channel card.
I have a dual G5 XServe with one of the standard 250gb SATA drives in 
/dev/sda

Everything works fine, until I try to install an LSI 7202P fibre channel 
adapter card. There is nothing connected to the fibre channel 
adapter, and a video card in the other pci slot.

The boot sequence starts, and then dies with the following error: "Oops: 
Kernel access of bad area, sig: 11 [#1]"

I get this error with both smp/up kernels, and have verified the MPT 
fusion driver is compiled into the YDL G5 kernel. Is this a problem with 
the driver/card/kernel? Has anyone had anything similar occur? I noted one 
person who had an NFS problem, but that didn't seem to be the same thing.

Below is the disk controller output from the serial port on the crash.

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with 
idebus=xx
adb: finished probe task...
ide0: Found Apple K2 ATA-6 controller, bus ID 3, irq 39
hda: QSI CD-ROM TCR-241, ATAPI CD/DVD-ROM drive
hda: Set MDMA timing for mode 2, reg: 0x08148a92
hda: Enabling MultiWord DMA 2
elevator: using anticipatory as default io scheduler
ide0 at 0xe000000083dc7000-0xe000000083dc7007,0xe000000083dc7160 on irq 39
hda: ATAPI 24X CD-ROM drive, 512kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
ata1: SATA max UDMA/133 cmd 0xE000000083DC9000 ctl 0xE000000083DC9020 
bmdma 0xE000000083DC9030 irq 0
ata2: SATA max UDMA/133 cmd 0xE000000083DC9100 ctl 0xE000000083DC9120 
bmdma 0xE000000083DC9130 irq 0
ata3: SATA max UDMA/133 cmd 0xE000000083DC9200 ctl 0xE000000083DC9220 
bmdma 0xE000000083DC9230 irq 0
ata4: SATA max UDMA/133 cmd 0xE000000083DC9300 ctl 0xE000000083DC9320 
bmdma 0xE000000083DC9330 irq 0
ata1: dev 0 ATA, max UDMA/100, 490234752 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_svw
ata2: no device found (phy stat 00000004)
scsi1 : sata_svw
ata3: no device found (phy stat 00000004)
scsi2 : sata_svw
ata4: no device found (phy stat 00000004)
scsi3 : sata_svw
  Vendor: ATA       Model: Hitachi HDS72252  Rev: V3UB
  Type:   Direct-Access                      ANSI SCSI revision: 05
st: Version 20041025, fixed bufsize 32768, s/g segs 256
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sda: drive cache: write back
 sda: [mac] sda1 sda2 sda3 sda4 sda5
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
Fusion MPT base driver 3.01.18
Copyright (c) 1999-2004 LSI Logic Corporation
mptbase: Initiating ioc0 bringup
ioc0: FC929: Capabilities={Initiator,Target,LAN}
mptbase: Initiating ioc1 bringup
ioc1: FC929: Capabilities={Initiator,Target,LAN}
Fusion MPT SCSI Host driver 3.01.18
scsi4 : ioc0: LSIFC929, FwRev=01000600h, Ports=1, MaxQ=1023, IRQ=53
scsi5 : ioc1: LSIFC929, FwRev=01000600h, Ports=1, MaxQ=1023, IRQ=53
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2 POWERMAC
NIP: C00000000029F814 XER: 0000000020000000 LR: C000000000297CDC
REGS: c0000000004d33b0 TRAP: 0300   Not tainted  (2.6.10-1.ydl.1g5-smp)
MSR: 9000000000009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 000000010fed3848, DSISR: 0000000040000000
TASK: c0000000005328e0[0] 'swapper' THREAD: c0000000004d0000 CPU: 0
GPR00: C000000000297CDC C0000000004D3630 C0000000006D1380 C0000000020A6000
GPR04: C0000000004D6080 0000000000000001 C0000000004CE650 000000000027F000
GPR08: C0000000020A6000 C00000000029C150 0000000000010000 C00000000029C090
GPR12: 9000000000009032 C00000000051D800 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000001400000 0000000000000000 00000000018A4AC0 000000000000000A
GPR24: 0000000000000000 C0000000006CE208 0000000000000000 C0000000004CE000
GPR28: C0000000020A6034 C0000000020A6000 000000010FED3800 C0000000004D3630
NIP [c00000000029f814] .scsi_device_unbusy+0x34/0xd0
LR [c000000000297cdc] .scsi_finish_command+0x3c/0x104
Call Trace:
[c0000000004d3630] [0000000001400000] 0x1400000 (unreliable)
[c0000000004d36d0] [c000000000297cdc] .scsi_finish_command+0x3c/0x104
[c0000000004d3760] [c000000000298144] .scsi_softirq+0x16c/0x17c
[c0000000004d3800] [c000000000047538] .__do_softirq+0xcc/0x1bc
[c0000000004d38c0] [c0000000000476b0] .do_softirq+0x88/0x8c
[c0000000004d3950] [c000000000066e1c] .irq_exit+0x70/0x8c
[c0000000004d39d0] [c00000000000f0d4] .do_IRQ+0x74/0xc0
[c0000000004d3a60] [c00000000000ae34] HardwareInterrupt_entry+0x8/0x54
--- Exception: 501 at .power4_idle+0x88/0x90
    LR = .native_idle+0x4c/0x54
[c0000000004d3d50] [c00000000000f578] .native_idle+0x38/0x54 (unreliable)
[c0000000004d3dd0] [c00000000000f47c] .cpu_idle+0x3c/0x58
[c0000000004d3e50] [c00000000000c4e8] .rest_init+0x3c/0x58
[c0000000004d3ed0] [c00000000047b830] .start_kernel+0x27c/0x2fc
[c0000000004d3f90] [c00000000000c0a8] .__setup_cpu_power3+0x0/0x4
 <0>Kernel panic - not syncing: Fatal exception in interrupt
 <0>Rebooting in 180 seconds..


Thanks,

Randy

http://www.frenzy.org
"Sed Quis Custodiet Ipsos Custodes?" -Juvenal