YDL 4.0 no Network
Felix Jodoin
felixj at shaw.ca
Thu Mar 24 19:36:37 MST 2005
The module sungem needs to be loaded after sungem_phy.
-Felix
On Thu, 2005-03-24 at 18:57 -0700, Bruce Woller wrote:
> Hello Steve:
> I have a G3 B&W 450 with a "GMAC(SUN GEM) Manufacturer:Apple Computer,
> Driver: sungem, Device: /dev/eth0" according to the Hardware Browser.
> I am using it to send this e-mail - I installed YDL4.0 straight out of
> the box and eth0 just came up all on its own. I wonder if the driver
> failed to install on your system?
>
> (Just so Terrasoft knows that not all G3s have a problem.)
>
> Bruce
> On Fri, 2005-03-25 at 09:41, Steve Meyer wrote:
> > Interesting new development...
> >
> > After three installs of YDL, I realized I was never prompted to
> > selectDHCP or manual IP config. Now, with a different NIC (3Com)
> > installed,and after running the YDL CD installation again, the NIC is
> > listed andI get prompted to choose my IP configuration! So, the
> > problem wasrelated to YDL/Fedora not recognizing the onboard NIC.
> > This may beimportant for the Blue & White G3 "hardware supported"
> > notes onTerrasoft's web site.
> >
> > Steve
> >
> > On Mar 25, 2005, at 9:31 AM, Steve Meyer wrote:
> >
> > From previous conversation...
> > "SM> when I do 'ifconfig -a' I do not see a MAC address
> > listed.
> > ----------------------------------------------------------
> > Current conversation:
> > RS> You don't see something like this?
> >
> > "eth0 Link encap:Ethernet HWaddr 00:0a:43:75:96:3A"
> >
> >
> > No, I don't...no MAC address is listed.
> >
> > RS> "It should be... after you run ifup, 'service iptables
> > status' (asroot) should
> > show the firewall config.."
> >
> > When i ran 'ifup eth0' I get "configuration for eth0 not
> > found."message. Yet in the GUI side 'System Settings/Network',
> > the hardwaretab lists GMAC (Sun GEM) as eth0 and it says it's
> > status is "ok".
> >
> > RS> "you can use tcpdump (as root) to watch traffic, to see if
> > you aregetting dhcp
> > replies..
> >
> > tcpdump -l -i eth0"
> >
> > Again I have problems running tcpdump...I think this is due to
> > thefact that there is no Ethernet card configured? The G3 Blue
> > and Whitewas on the YDL supported hardware list with no issues
> > regarding theonboard NIC. I would like to use the same NIC
> > that works with Mac OSX but wonder if I should setup a
> > different NIC in the computer so Ican network in
> > Linux...however, that card will most likely not workwith OS X?
> >
> > Thanks for all your help,
> >
> > Steve
> >
> >
> >
> >
> >
> >
> > Greetings,
> >
> > I have a Blue and White G3 (300Mhz) that is getting on
> > the network(built in E-net) on the Mac OS X side but
> > when I boot to Yellowdog Ifind I cannot browse via
> > Mozilla...it's like my NIC is not getting anIP. I
> > reinstalled Yellowdog and still have the problem. If
> > I go toSystem Settings/Network and login at the prompt
> > as root, under theHardware tab it shows "GMAC (Sun
> > GEM) Ethernet eth0 ok". Any ideas?
> >
> > Thanks!
> >
> > _______________________________________________
> > yellowdog-general mailing list
> > yellowdog-general at lists.terrasoftsolutions.com
> > http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-general
> > HINT: to Google archives, try
> > '<keywords>site:terrasoftsolutions.com'
> >
> >
> >
> > ______________________________________________________________________
> > _______________________________________________
> > yellowdog-general mailing list
> > yellowdog-general at lists.terrasoftsolutions.com
> > http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-general
> > HINT: to Google archives, try '<keywords> site:terrasoftsolutions.com'
>
> _______________________________________________
> yellowdog-general mailing list
> yellowdog-general at lists.terrasoftsolutions.com
> http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-general
> HINT: to Google archives, try '<keywords> site:terrasoftsolutions.com'
More information about the yellowdog-general
mailing list