Setting up WiFi on PB with AirPort Extreme - Part 1
Ebrahim Mayat
ebmayat at mac.com
Tue Aug 15 15:23:31 MDT 2006
Dear list
I setup my internal AirPort Extreme wireless card using the "script"
shown below. I am, however, unable to send/receive e-mail or bring up
web pages. Some details and diagnostics:
# modprobe ieee80211softmac
# modprobe bcm43xx
# ifconfig eth1 up
# ip link set eth1 up
# ifconfig
eth1 Link encap:Ethernet HWaddr 00:11:24:a2:d2:5d
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:10 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:52 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1593 errors:0 dropped:0 overruns:0 frame:0
TX packets:1593 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1973874 (1.8 MiB) TX bytes:1973874 (1.8 MiB)
# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
Warning: Driver for device eth1 has been compiled with version 20
of Wireless Extension, while this program supports up to version 17.
Some things may be broken...
eth1 IEEE 802.11b/g ESSID:off/any Nickname:"Broadcom 4306"
Mode:Managed Frequency=2.437 GHz Access Point:
FF:FF:FF:FF:FF:FF
Bit Rate:11 Mb/s Tx-Power=15 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sit0 no wireless extensions.
# iwconfig eth1 essid Myessid
# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
Warning: Driver for device eth1 has been compiled with version 20
of Wireless Extension, while this program supports up to version 17.
Some things may be broken...
eth1 IEEE 802.11b/g ESSID:"Myessid" Nickname:"Broadcom 4306"
Mode:Managed Frequency=2.462 GHz Access Point:
00:11:24:a2:d2:5d
Bit Rate:11 Mb/s Tx-Power=15 dBm
RTS thr:off Fragment thr:off
Encryption key:off
[root at localhost ~]# ip link show eth1
3: eth1: <BROADCAST,MULTICAST,UP,10000> mtu 1500 qdisc pfifo_fast
qlen 1000
link/ether 00:11:24:a2:d2:5d brd ff:ff:ff:ff:ff:ff
# iwlist eth1 scan
Warning: Driver for device eth1 has been compiled with version 20
of Wireless Extension, while this program supports up to version 17.
Some things may be broken...
eth1 Scan completed :
Cell 01 - Address: 00:11:24:a2:d2:5d
ESSID:"Myessid"
Protocol:IEEE 802.11bg
Mode:Master
Channel:11
Encryption key:off
Bit Rate:54 Mb/s
Extra: Rates (Mb/s): 1 2 5.5 6 9 11 12 18 24 36
48 54
Quality=100/100 Signal level=-144 dBm
Extra: Last beacon: 43ms ago
Cell 02 - Address: 00:11:24:45:66:2e
ESSID:"neighbouressid"
Protocol:IEEE 802.11bg
Mode:Master
Channel:11
Encryption key:off
Bit Rate:54 Mb/s
Extra: Rates (Mb/s): 1 2 5.5 9 11 6 12 18 24 36
48 54
Quality=100/100 Signal level=-203 dBm
Extra: Last beacon: 29ms ago
Link Quality=100/100 Signal level=2/3 Noise level=185/100
Rx invalid nwid:0 Rx invalid crypt:33 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sit0 no wireless extensions.
...
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.terrasoftsolutions.com/pipermail/yellowdog-newbie/attachments/20060815/f347b854/attachment-0001.htm
More information about the yellowdog-newbie
mailing list