Subject: Re: Keyboard failure?
From: Romeyn Prescott (prescor@digirom.potsdam.edu)
Date: Mon Apr 02 2001 - 09:48:04 MDT
Somewhen around 7:59 AM -0600 4/2/01, a person believing themself to
be Derrik Pates scribbled:
>On Mon, 2 Apr 2001, Romeyn Prescott wrote:
>
>> I don't have a line like that! I'm using the default file (duly
>> tweaked, of course) and that entry is nowhere to be found! I'm going
>> to try rebooting and watching the boot sequence for indication of my
>> Keyboard's ID, but it goes by so damned FAST!!!
>
>Do 'dmesg | less' instead of rebooting, so you can page through the boot
messages and find anything applicable.
From the sample molrc file:
-----
# Hint: *Usually* the ID is printed during Linux/PPC's bootup.
# .....
# adb devices: [2]: 2 22 [3]: 3 1
# ^ ^
# | +- The second number ("22" here) is the
keyboard ID.
# This "2" indicates that it's an ADB keyboard.
-----
Here's a snippet from /var/log/dmesg (entire dump follows message):
-----
usb.c: USB new device connect, assigned device number 3
keybdev.c: Adding keyboard: input1
event1: Event device for input1
input1: USB HID v10.01 Keyboard [Mitsumi Electric Apple Extended USB
Keyboard] o
n usb1:3.0
keybdev.c: Adding keyboard: input2
event2: Event device for input2
input2: USB HID v10.01 Device [Mitsumi Electric Apple Extended USB Keyboard] on
usb1:3.1
-----
This is the only thing I can find that applies, but I don't know how
to translate this information into a keyboard ID for use/entry in
molrc. I'm almost there and can taste victory. Any more ideas?
...ROMeyn
-----
device tree used 42112 bytes
Total memory = 128MB; using 512kB for hash table (at c0280000)
Linux version 2.2.18-4hpmac (root@entropy.crashing.org) (gcc version
2.95.3 2000
1220 (prerelease/franzo/20001220)) #1 Thu Dec 21 15:16:15 MST 2000
PCI bus 0 controlled by pci at f0000000
PCI buses 0..1 controlled by pci at f2000000
PCI bus 0 controlled by pci at f4000000
Uni-N revision: 3, KeyLargo revision: 2
Registered 1 feature controller(s)
PMU driver initialized for Core99
pmac nvram is core99: 1
PowerMac using OpenPIC irq controller
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at efee3000
GMT Delta read from XPRAM: 0 minutes, DST: off
via_calibrate_decr: decrementer_count = 249086 (1494519 ticks)
Console: colour dummy device 80x25
Calibrating delay loop... 796.26 BogoMIPS
Memory: 126788k available (1408k kernel code, 2724k data, 152k init)
[c0000000,c
8000000]
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Starting kswapd v 1.5
clgen: Driver for Cirrus Logic based graphic boards, v1.5.2
Couldn't find PCI device
aty128fb: detected XCLK=0x36d6, ref_div=0x35
aty128fb: Rage128 Pro PF (AGP) [chip rev 0x1] 16M 128-bit SDR SGRAM (1:1)
Console: switching to colour frame buffer device 160x64
fb0: ATY Rage128 frame buffer device on /pci@f0000000/ATY,Rage128Ps@10
input0: Macintosh mouse button emulation
PowerMac Z8530 serial driver version 2.0
tty00 at 0xcd00d020 (irq = 22) is a Z8530 ESCC
tty01 at 0xcd014000 (irq = 50) is a Z8530 ESCC
pty: 256 Unix98 ptys configured
Macintosh non-volatile memory driver v1.0
pmac_ide: enabling IDE bus ID 2
pmac_ide: enabling IDE bus ID 0
pmac_ide: enabling IDE bus ID 1
hda: WDC WD136AA, ATA DISK drive
hdc: MATSHITAPD-2 LF-D110, ATAPI CDROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide0 at 0xdb01a000-0xdb01a007,0xdb01a160 on irq 19
ide1 at 0xdb01e000-0xdb01e007,0xdb01e160 on irq 20
hda: Enabling Ultra DMA 4
hda: WDC WD136AA, 12971MB w/2048kB Cache, CHS=26354/16/63, (U)DMA
(scsi0) <Adaptec AIC-7850 SCSI host adapter> found at PCI 1/2/0
(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi0) Cables present (Int-50 NO, Ext-50 YES)
(scsi0) Downloading sequencer code... 415 instructions downloaded
sym53c8xx: at PCI bus 1, device 3, function 0
sym53c8xx: setting PCI_COMMAND_IO PCI_COMMAND_MEMORY...
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c875 detected
sym53c875-0: rev 0x4 on pci bus 1 device 3 function 0 irq 53
sym53c875-0: ID 7, Fast-20, Parity Checking
ncr53c8xx: at PCI bus 1, device 3, function 0
ncr53c8xx: IO region 0x1000[0..127] is in use
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<Adaptec AIC-7850 SCSI host adapter>
scsi1 : sym53c8xx-1.7.1-20000726
scsi : 2 hosts.
Vendor: IOMEGA Model: Io20S *F Rev: 1.7
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sda at scsi0, channel 0, id 1, lun 0
Unlocked floptical drive.
(scsi0:0:2:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: SEAGATE Model: ST39140N Rev: 1498
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 2, lun 0
(scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: iomega Model: jaz 1GB Rev: J.86
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sdc at scsi0, channel 0, id 3, lun 0
(scsi0:0:4:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: iomega Model: jaz 1GB Rev: H.72
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi removable disk sdd at scsi0, channel 0, id 4, lun 0
Vendor: YAMAHA Model: CRW4260 Rev: 1.0q
Type: CD-ROM ANSI SCSI revision: 02
Vendor: QUANTUM Model: VIKING 4.5 WSE Rev: 880P
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sde at scsi1, channel 0, id 0, lun 0
Vendor: QUANTUM Model: VIKING 4.5 WSE Rev: 880P
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdf at scsi1, channel 0, id 1, lun 0
scsi : detected 6 SCSI disks total.
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 28
sda : extended sense code = 2
sda : block size assumed to be 512 bytes, disk size 1GB.
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17783240 [8683 MB] [8.7 GB]
sdc : READ CAPACITY failed.
sdc : status = 1, message = 00, host = 0, driver = 28
sdc : extended sense code = 2
sdc : block size assumed to be 512 bytes, disk size 1GB.
sdd : READ CAPACITY failed.
sdd : status = 1, message = 00, host = 0, driver = 28
sdd : extended sense code = 2
sdd : block size assumed to be 512 bytes, disk size 1GB.
sym53c875-0-<0,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
SCSI device sde: hdwr sector= 512 bytes. Sectors= 8899737 [4345 MB] [4.3 GB]
sym53c875-0-<1,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
SCSI device sdf: hdwr sector= 512 bytes. Sectors= 8899737 [4345 MB] [4.3 GB]
eth0: GMAC at 00:0a:27:b4:ba:6a, driver v1.3k2
3c59x.c 15Sep00 Donald Becker and others
http://www.scyld.com/network/vortex.htm
l
Partition check:
sda:scsidisk I/O error: dev 08:00, sector 0
unable to read partition table
sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
sdc:scsidisk I/O error: dev 08:20, sector 0
unable to read partition table
sdd:scsidisk I/O error: dev 08:30, sector 0
unable to read partition table
sde: sde1 sde2 sde3 sde4 sde5 sde6
sdf: sdf1 sdf2 sdf3 sdf4 sdf5 sdf6 sdf7
hda: hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13
event0: Event device for input0
usb.c: registered new driver hid
mouse0: PS/2 mouse device for input0
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Enabling bus mastering for device 01:40
usb-ohci.c: USB OHCI at membase 0xcd039000, IRQ 27
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling bus mastering for device 01:48
usb-ohci.c: USB OHCI at membase 0xcd03b000, IRQ 28
usb.c: new USB bus registered, assigned bus number 2
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 152k init 28k prep
usb.c: USB new device connect, assigned device number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb.c: USB new device connect, assigned device number 3
keybdev.c: Adding keyboard: input1
event1: Event device for input1
input1: USB HID v10.01 Keyboard [Mitsumi Electric Apple Extended USB
Keyboard] o
n usb1:3.0
keybdev.c: Adding keyboard: input2
event2: Event device for input2
input2: USB HID v10.01 Device [Mitsumi Electric Apple Extended USB Keyboard] on
usb1:3.1
usb.c: USB new device connect, assigned device number 4
mouse1: PS/2 mouse device for input3
event3: Event device for input3
input3: USB HID v10.01 Mouse [Fujitsu Takamisawa Component Apple
Optical USB Mou
se] on usb1:4.0
grep uses obsolete /proc/pci interface
DMA sound driver installed, using 4 buffers of 32k.
--signat-url: http://www2.potsdam.edu/dctm/prescor/signat-url.htm cubiclecam: http://digirom.potsdam.edu/~prescor/cubiclecam.html ^^^ <--- Off-line unless someone knows how to get camserv to compile under RedHat 7... *sigh* :-(
This archive was generated by hypermail 2a24 : Mon Apr 02 2001 - 09:50:51 MDT