zip drives
Andrew
yellowdog-general@lists.terrasoftsolutions.com
Sat Apr 10 09:58:01 2004
On Sat, 2004-04-10 at 00:43, James A. Ricken wrote:
> Andrew wrote:
>
> >
> >Im go for a beer, its fryday after all!
> >
> >spawn a terminal and follow those steps (I'll assume you are using KDE
> >for the desktop-icon section)
> >
> >First, let see if its (even) recognized by the system during booting:
> >(subdue SCSI for USB if you use a USB model..)
> >
> >Ok Andrew I sent you my History
> >
> >
> Hopefully You or someone will be able to help
> Thanks
> Jim
>
>
> ______________________________________________________________________
>
> [jim@localhost jim]$ dmesg | more
> Memory BAT mapping: BAT2=256Mb, BAT3=128Mb, residual: 368Mb
> Total memory = 496MB; using 1024kB for hash table (at c0400000)
> Linux version 2.4.22-2f (dburcaw@skyfox.terraplex.com) (gcc version 3.2.2 200302
> 17 (Yellow Dog Linux 3.0 3.2.2-2a)) #1 Sun Nov 9 16:49:49 EST 2003
> Found a Grand Central mac-io controller, rev: 2, mapped at 0xfdd7f000
> PowerMac motherboard: PowerMac 8500/8600
> Cache coherency enabled for bandit/PSX
> Found Bandit PCI host bridge at 0xf2000000. Firmware bus number: 0->0
> hose bandit, pci_mem_offset: 00000000, start0: f3000000
> io_base_virt: fd57c000, io_base_phys: f2000000, isa_mem_base: 00000000
> Found Chaos PCI host bridge at 0xf0000000. Firmware bus number: 1->1
> hose chaos, pci_mem_offset: 00000000, start0: f1000000
> io_base_virt: fcd7a000, io_base_phys: f0000000, isa_mem_base: 00000000
> nvram: OF partition at 0x1800
> nvram: XP partition at 0x1300
> nvram: NR partition at 0x1400
> On node 0 totalpages: 126976
> zone(0): 126976 pages.
> zone(1): 0 pages.
> zone(2): 0 pages.
> Kernel command line: root=/dev/hdd8
> System has 32 possible interrupts
> GMT Delta read from XPRAM: -300 minutes, DST: on
> via_calibrate_decr: ticks per jiffy = 125004 (750027 ticks)
> Console: colour dummy device 80x25
> Calibrating delay loop... 799.53 BogoMIPS
> Memory: 496808k available (2228k kernel code, 1148k data, 176k init, 0k highmem)
> Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
> Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
> Mount cache hash table entries: 512 (order: 0, 4096 bytes)
> Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
> Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
> POSIX conformance testing by UNIFIX
> PCI: Probing PCI hardware
> Scanning bus 00
> Found 00:58 [106b/0001] 000600 00
> Found 00:68 [1191/0007] 000100 00
> Found 00:70 [1045/c861] 000c03 00
> Found 00:78 [1002/5245] 000300 00
> Found 00:80 [106b/0002] 00ff00 00
> Fixups for bus 00
> Bus scan for 00 returning with max=00
> Scanning bus 01
> Found 01:58 [106b/0003] 000000 00
> Found 01:68 [106b/0004] 00ff00 00
> Fixups for bus 01
> Bus scan for 01 returning with max=01
> PCI: bridge rsrc 0..7fffff (100), parent c0287194
> PCI: bridge rsrc f3000000..f3ffffff (200), parent c02871b0
> PCI: bridge rsrc 80000000..8fffffff (200), parent c02871b0
> PCI: bridge rsrc ff7fe000..ffffdfff (100), parent c0287194
> PCI: bridge rsrc f1000000..f1ffffff (200), parent c02871b0
> PCI: bridge rsrc 90000000..9fffffff (200), parent c02871b0
> PCI:00:0d.0: Resource 0: 00000840-00000847 (f=101), vd: 1191, dev: 0007
> PCI:00:0d.0: Resource 1: 00000830-00000833 (f=101), vd: 1191, dev: 0007
> PCI:00:0d.0: Resource 2: 00000820-00000827 (f=101), vd: 1191, dev: 0007
> PCI:00:0d.0: Resource 3: 00000810-00000813 (f=101), vd: 1191, dev: 0007
> PCI:00:0d.0: Resource 4: 00000800-0000080f (f=101), vd: 1191, dev: 0007
> PCI:00:0f.0: Resource 0: 88000000-8bffffff (f=1208), vd: 1002, dev: 5245
> PCI:00:0f.0: Resource 2: 80804000-80807fff (f=200), vd: 1002, dev: 5245
> PCI:00:10.0: Resource 0: f3000000-f301ffff (f=200), vd: 106b, dev: 0002
> PCI:00:0e.0: Resource 0: 80800000-80800fff (f=200), vd: 1045, dev: c861
> PCI:00:0f.0: Resource 1: 00000400-000004ff (f=101), vd: 1002, dev: 5245
> PCI:01:0b.0: Resource 1: 90000000-9000ffff (f=200), vd: 106b, dev: 0003
> PCI:01:0b.0: Resource 2: 94000000-97ffffff (f=200), vd: 106b, dev: 0003
> PCI:01:0d.0: Resource 0: 90000000-900003ff (f=200), vd: 106b, dev: 0004
> resource conflict with: 90000000..9000ffff (200), name: Apple Computer Inc. Cont
> rol Video
> PCI: Cannot allocate resource region 0 of device 01:0d.0
> PCI: parent is c03f8070: 90000000-9fffffff (f=200)
> PCI: moved device 01:0d.0 resource 0 (200) to f1000000
> Macintosh CUDA driver v0.5 for Unified ADB.
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> Thermal assist unit using timers, shrink_timer: 200 jiffies
> Starting kswapd
> VFS: Disk quotas vdquot_6.5.1
> Journalled Block Device driver loaded
> Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> udf: registering filesystem
> PCI: Enabling device 00:0f.0 (0086 -> 0087)
> aty128fb: Rage128 RE (PCI) [chip rev 0x2] 16M 128-bit SDR SGRAM (1:1)
> Console: switching to colour frame buffer device 128x48
> fb0: ATY Rage128 frame buffer device on PCI
> controlfb: VRAM Total = 0MB (0MB @ bank 1, 0MB @ bank 2)
> MacOS display is /bandit/ATY,Rage128y
> input0: Macintosh mouse button emulation
> pty: 256 Unix98 ptys configured
> fd0: SWIM3 floppy controller
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> loop: loaded (max 8 devices)
> eth0: MACE at 00:05:02:2e:79:15, chip revision 25.64
> Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> AEC6260R: IDE controller at PCI slot 00:0d.0
> AEC6260R: chipset revision 1
> AEC6260R: not 100% native mode: will probe irqs later
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> AEC6260R: ROM enabled at 0x80810000
> ide0: BM-DMA at 0x0800-0x0807, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0x0808-0x080f, BIOS settings: hdc:pio, hdd:pio
> Probing IDE interface ide0...
> hda: ST310240A, ATA DISK drive
> Unhandled interrupt 17, disabled
> blk: queue c034e020, I/O limit 4095Mb (mask 0xffffffff)
> Probing IDE interface ide1...
> hdd: WDC WD153AA-53BAA0, ATA DISK drive
> blk: queue c034e5d8, I/O limit 4095Mb (mask 0xffffffff)
> ide0 at 0x840-0x847,0x832 on irq 23
> ide1 at 0x820-0x827,0x812 on irq 23
> hda: attached ide-disk driver.
> hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: task_no_data_intr: error=0x04 { DriveStatusError }
> hda: 19541088 sectors (10005 MB) w/128KiB Cache, CHS=19386/16/63, UDMA(33)
> hdd: attached ide-disk driver.
> hdd: host protected area => 1
> hdd: 30064608 sectors (15393 MB) w/2048KiB Cache, CHS=29826/16/63, UDMA(33)
> Partition check:
> hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7
> hdd: [mac] hdd1 hdd2 hdd3 hdd4 hdd5 hdd6 hdd7 hdd8 hdd9 hdd10
> SCSI subsystem driver Revision: 1.00
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> mesh: configured for synchronous 5 MB/s
> mesh: performing initial bus reset...
> scsi1 : MESH
> mesh: target 0 synchronous at 5.0 MB/s
> Vendor: QUANTUM Model: FIREBALL ST4300S Rev: 0F0D
> Type: Direct-Access ANSI SCSI revision: 02
> mesh: target 3 synchronous at 5.0 MB/s
> Vendor: MATSHITA Model: CD-ROM CR-8024 Rev: 2.0e
> Type: CD-ROM ANSI SCSI revision: 02
> Vendor: IOMEGA Model: ZIP 100 Rev: E.08
> Type: Direct-Access ANSI SCSI revision: 02
> scsi2 : 53C94
> Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
> Attached scsi removable disk sdb at scsi1, channel 0, id 5, lun 0
> SCSI device sda: 8418816 512-byte hdwr sectors (4310 MB)
> sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9
> sdb: Unit Not Ready, sense:
> Current 00:00: sense key Not Ready
> Additional sense indicates Medium not present
> sdb : READ CAPACITY failed.
> sdb : status = 1, message = 00, host = 0, driver = 08
> Current sd00:00: sense key Not Ready
> Additional sense indicates Medium not present
> sdb : block size assumed to be 512 bytes, disk size 1GB.
> sdb: I/O error: dev 08:10, sector 0
> I/O error: dev 08:10, sector 0
> unable to read partition table
> Attached scsi CD-ROM sr0 at scsi1, channel 0, id 3, lun 0
> sr0: scsi-1 drive
> Uniform CD-ROM driver Revision: 3.12
> PowerMac Z8530 serial driver version 2.0
> tty00 at 0xe10da020 (irq = 15) is a Z8530 ESCC, port = modem
> tty01 at 0xe10dd000 (irq = 16) is a Z8530 ESCC, port = printer
> Macintosh non-volatile memory driver v1.0
> apm_emu: Requires a machine with a PMU.
> usb.c: registered new driver usbdevfs
> usb.c: registered new driver hub
> PCI: Enabling device 00:0e.0 (0014 -> 0016)
> host/usb-ohci.c: USB OHCI at membase 0xe10df000, IRQ 24
> host/usb-ohci.c: usb-00:0e.0, OPTi Inc. 82C861
> adb: starting probe task...
> usb.c: new USB bus registered, assigned bus number 1
> hub.c: USB hub found
> hub.c: 2 ports detected
> usb.c: registered new driver hid
> hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
> hid-core.c: USB HID support drivers
> mice: PS/2 mouse device common for all mice
> Initializing Cryptographic API
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 4096 buckets, 32Kbytes
> TCP: Hash tables configured (established 32768 bind 65536)
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 176k init 8k chrp 8k prep
> adb devices: [2]: 2 2 [3]: 3 1
> ADB keyboard at 2, handler set to 3
> Detected ADB keyboard, type ANSI.
> input1: ADB HID on ID 2:2.02
> ADB mouse at 3, handler set to 2
> input2: ADB HID on ID 3:3.01
> adb: finished probe task...
> hub.c: new USB device 00:0e.0-2, assigned address 2
> hub.c: USB hub found
> hub.c: 3 ports detected
> hub.c: new USB device 00:0e.0-2.1, assigned address 3
> input: USB HID v10.01 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on
> usb1:3.0
> input: USB HID v10.01 Device [Mitsumi Electric Apple Extended USB Keyboard] on u
> sb1:3.1
> EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,72), internal journal
> hub.c: new USB device 00:0e.0-2.2, assigned address 4
> usb.c: USB device 4 (vend/prod 0x43d/0x57) is not claimed by any active driver.
> Adding Swap: 651424k swap-space (priority -1)
> Adding Swap: 511992k swap-space (priority -2)
> hub.c: new USB device 00:0e.0-2.3, assigned address 5
> input: USB HID v10.01 Mouse [Logitech USB-PS/2 Optical Mouse] on usb1:5.0
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,73), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> usb.c: registered new driver usblp
> printer.c: usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x043D
> pid 0x0057
> printer.c: v0.11: USB Printer Device Class driver
> ip_tables: (C) 2000-2002 Netfilter core team
> i2c-core.o: i2c core module
> dmasound_pmac: Awacs/Screamer Codec Mfct: 1 Rev 2
> PowerMac AWACS rev 2 DMA sound driver rev 016 installed
> Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
> Write will use 4 fragments of 32768 bytes as default
> Read will use 4 fragments of 32768 bytes as default
> sdb: Unit Not Ready, sense:
> Current 00:00: sense key Not Ready
> Additional sense indicates Medium not present
> sdb : READ CAPACITY failed.
> sdb : status = 1, message = 00, host = 0, driver = 08
> Current sd00:00: sense key Not Ready
> Additional sense indicates Medium not present
> sdb : block size assumed to be 512 bytes, disk size 1GB.
> sdb: Write Protect is off
> sdb: I/O error: dev 08:10, sector 0
> I/O error: dev 08:10, sector 0
> unable to read partition table
> [jim@localhost jim]$
> [jim@localhost jim]$
> [jim@localhost jim]$
> [jim@localhost jim]$
> [jim@localhost jim]$
> [jim@localhost jim]$
what kind of zip is that? It sure look like a JAZ drive to me. Iomega
produce some 750MB zip but no 1000MB.
<http://www.iomega.com/na/products/>
As for all those errors related to sdb, make sure there is a disk in the
drive.