relocation

[Aurelio Bay]

Hi,

I have installed a new ATA disk Seagate ST340016A on a G3 B&W.
I experienced R/W errors. Following the instructions from FWB,
I reconfigured from UltraDMA2 to Multiword DMA2 using HDT.

Then I installed YD 2.3 on a free portion of the same disk.
During boot, I get the following msgs:
============

hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
end_request: I/O error, dev 03:08 (hda), sector 2888136
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success

================

Then the system comes up without any problmes (apparently).


Any suggestion on how to reconfigure the system to get a correct
behaviour ?

Thanks,


                                                      Aurelio BAY
_____________________________________________________________________________
Lausanne University,          INSTITUT DE PHYSIQUE DES HAUTES ENERGIES (IPHE)
BSP 616     CH-1015 Lausanne  SWITZERLAND
Lausanne Tel: +41 21 692 3702   Fax: +41 21 692 3705    
CERN:         +41 22 767 2518  (B2 1-024)
Aurelio.Bay@iphe.unil.ch    Aurelio.Bay@cern.ch    http://www-iphe.unil.ch/~bay